Jump to content

Recommended Posts

Hello Sondors riders! 

Just want to show you guys and gals the new KT-LCD3 now with a USB port! It still looks the same, functions the same except it now has a USB port in the back so you can charge your phone or power your headlights. Has a 5v output with 2.1amp to charge the latest Samsung & iphones. See more information here https://electrobikeworld.com/products/kt-lcd3-usb

 

 

LCD with USB2.jpg

  • Like 1
Link to post
Share on other sites
  • 2 years later...

Hi, I have the KT-LCD3 on my e bike and setting up the wheel size I’ve found 21 22 options are missing it just goes from 23 to 20 inch, 23 is the nearest I can set but is still not that accurate I need to go down to 22. I’ve got 20 x 4 fat tyres.

Thank you Mick

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Adam Seldow
      Battery on 2019 Sondors Step will not charge. I plug the charger into it and charger light remains green (never turns red to indicate charging). I reset LCD to default just to make sure it want settings issue. Any ideas? I tried two different chargers as we ha e two of these bikes. When I remove battery and plug in to charger, 3 green dot lights turn on only when plugged in. 
    • By Mennis
      Does anyone know how to correct this?
      My LCD displays 49.6 mph whenever I am coasting. The mph displays correct MPH whenever I am pedaling or using the throttle. 
      350 watt motor, 15 amp controller , 12.8 bottle battery, 
      KT-LCD3 V1.0  4E  24/36/48V
    • By 3D-vice
      * The best way to use this video is to watch and write down the desired options, then exit and program your LCD. if you try and program while watching the video your LCD will timebout and none of the settings will be saved and you’ll have to keep starting over because of the length of Kyles explanations .
      Aftermarket LCD Display user manual (also applying for Sondors eBike LCD)
      KT3-LCD_short_en.pdf (english language 2-page manual)
      KT3-LCD_full_en.pdf (english version full manual, 2013)
      KT3-LCD_full_de.pdf (german version full manual)
      Programming the KT-LCD3 and KT-LCD8H Everything you need to know
      EDIT:  This manual is the current version for the KT-LCD3.  It includes different behavior in some of the settings and lists C13 (regenerative braking... not applicable to Sondors) and C14 - PAS assist strength tuning (applicable to Sondors)
      KT-LCD3_2015.pdf (English, v3.0, 2015)
    • By mossmatt
      DIY: S-LCD3 Meter for Sondors eBike
       
      This walkthrough is for those who purchased the non Sondors S-LCD3 with the white flat 5-pin connector. If you are not comfortible with soldering, then you may want to wait for the retail Sondors LCD in xmas 2015.
      Walkthrough by Matt Moss
      Downloadable at uberbills.com/DIY-SLCD3-Soldering.docx
      S-LCD3 purchased from BMSBattery.com

      Tools:
      Screwdriver
      Wire Strippers
      Soldering iron
      60/40 Solder

      Step 1: Attach LCD3 to handlebars

      Step 2: Snip off the useless white flat 5-pin connector.

      Step 3: Pull meter cable through top hole in sondors battery box. (no picture)

      Step 4: Snip off the round 5-pin female plug and strip all the wiring down a half inch.

      Step 5: Proceed to tin the stranded wire ends. tinning means to apply hot motlen solder to the stranded wire, which helps to solder two separate wires together.

      Step 6: Admire your soldering job and apply insulation. I used cheap electrical tape, but you should spend a few cents and get some shrink tube.
       



      Step 7: Double check that no exposed wire is showing, and test our your new lcd meter. Hold the center power button to turn on. To keep the backlight on for easy viewing, press and hold the up arrow. If you hold and press the down arrow, your bike will lurch forward at a walking speed, so be careful!

      FAQ:
      Q: I press and hold the up arrow like you said and my bike wants to go for a ride. What gives?
      A: You installed your LCD button upsidedown. Reverse it and you should be fine.
      Q: Halp! Why is my LCD screen upside down?
      A: You installed your LCD screen upside down. /reverse it and you should be fine.
      Q: After installing the LCD, I am unable to engage the throttle and the bike does not move, yet everything is on. What Gives?
      A: Check that the LCD screen is actually on, you must have the LCD turned on in order for you to power your bike and use the motor.

      If you have any questions, feel free to PM me (private eMails or information not permitted in open forum PM me).. Please include in the subject “Sondors Storm Owners Group”
      If this walkthrough helped you in any way, please consider donating! Have a nice day!
      paypal: private eMails or information not permitted in open forum PM me.
      btc: 1KFfPjPhngm1ZezWu1YUReNGXFpbfgxtoz
    • By DavidN
      I purchased the August 2018 run XS Fat and received in Jan 2019. The admin password for advanced settings is 1515.
       
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. By using this site, you agree to our Terms of Use and Privacy Policy.